McQuay MDS080BR Installation Guide Page 68
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
-68-
Design & installation Guide For McQuay MDS Multi System
Handling outdoor units
Please refer to the followings to move units; To use 4 supporting points to move units instead
of 3 points, to avoid unstable move and units drop off.
BACK
FRONT
FRONT
BACK
FRONT
FRONT
BACK
BACK
Ľ900m
m
¡450mm
Ľ600mm
BACK
BACK
FRONT
FRONT
BACK
FRONT
FRONT
BACK
Ľ
9
0
0
m
m
Ľ
4
5
0
m
m
Ľ450mm
Suspension ropes
<40
Protective pads
(2 ropes)
ă
>8
m
>8m
<40
ă
Notes:
Be careful in the moving of outdoor units.
Do not lift or move units with the package rope, as it is easy to
break and bring danger.
Do not directly touch the fins of units to avoid hurt of hand.
Do keep the plastic bag from the child.
Outdoor unit installation
To use concrete or supporter to build a base. Fully consider the floor strength, drainage
(discharge from the unit in operation), and pipes and cables layout. If the strength cannot
satisfy the requirement, the unit may fall off to damage the unit and injure people.
To fix the outdoor unit with screw bolt to avoid falling off by earthquake or strong wind.
Properly install the unit to defend against strong wind and earthquake better.
To take some shock resistance measures (such as using cushion and bumper bracket) to
avoid vibration passing to the installation part. The bottom panel and wall may cause
vibration and noise, depending on the installation condition.
To place the edge to the right position. Otherwise, the unstable unit may cause the
installation foot bent. Any improper installation may cause the unit falling off and injuring
people.
Warning:
The unit must be installed to the place which is strong enough to bear the unit weight and
vibration.
For lower pipes and cables layout, make sure the base not block the hole at the bottom.
When laying out the lower pipes, the basic height shall not be less 100 mm to ensure the
pipe to get through the unit bottom.
- CONTENTS 3
- Overview 4
- MDS080BR MDS100BR MDS120BR 7
- MDS150BR 7
- MDS200BR MDS220BR MDS240BR 8
- MDS180BR 8
- MDS280BR MDS300BR 9
- MDS260BR 9
- 1.3 Main Features 10
- Nominal capacity 11
- 100% operating 11
- 1.4 Nomenclature 12
- 1.5 Products Series 14
- 1.6 Performance Parameter 15
- 1.6.3 Ceiling Cassette 16
- 1.7 Operating Range 19
- 1.8 Refnet 19
- 1.8.2 C Type 20
- 1.9 Outline of Indoor Units 21
- 1.9.2 MDB050T 22
- 1.9.3 MDB060T 22
- 1.9.5 MCM020T MCM030T MCM050T 23
- 1.9.6 Auxiliary Heating Coil 24
- 1.10 Outline of Outdoor Units 25
- Unit Control 27
- Te m perature 28
- 2.3.3 Wire Control Panel 31
- 2.3.4 Outline and Dimension 31
- 2.3.5 Installation Type 31
- concealed installation 31
- 2.5 Network Central Control 34
- 2.6 Wiring Diagram 35
- Model MCK025/030/040/050T 36
- MCM020/030T 36
- Model MCM050T 37
- Model MDB050/060T 37
- Model MDS030A 38
- Model MDS030AR 38
- Model MDS040AR 39
- Model MDS040A 39
- Model MDS050A 40
- Model MDS050AR(220V~/50Hz) 40
- Model MDS060A 41
- Model MDS060AR(220V~/50Hz) 42
- Model MDS080/100/120B 43
- Model MDS080/100/120BR 43
- Model MDS150B 44
- Model MDS150BR 44
- Model MDS180B 45
- Model MDS180BR 45
- Model MDS200/220/240B 46
- Model MDS200/220/240BR 46
- Model MDS260BR(Master Unit) 47
- Connecting the master unit 48
- 2.7 Electric Connection 49
- 2.7.3 MDS080 240B/BR 50
- 2.7.4 MDS260 300B/BR 50
- 2.8 Electric Data 51
- Selection 52
- 3.2 Selection of Indoor Units 54
- Correction factor 57
- 3.4 Design of Air System 58
- 3.5 Slection of Refnet Joint 63
- For MDS-A series 64
- For MDS-B series 64
- Y type 65
- Type: MDS-Y5 65
- 3.6 Selection of E-EXV Box 66
- Installation 67
- Suspension ropes 68
- Protective pads 68
- (2 ropes) 68
- 4.2 Indoor Unit Installation 70
- (machine dimension) 820mm 73
- PULL PULL PULL PULL 76
- Height between indoor 78
- Refnet joint 80
- Outdoor unit 80
- Distributor kit 80
- Controller 81
- Indoor unit 81
- To indoor unit 82
- To outdoor unit 82
- Moisture 83
- Blind plug(copper) 84
- Flare fitting 84
- Avoid wielding too often 85
- Work flow 86
- NO.1 NO.2 87
- 6.4mm~25.4mm 10mm or more 88
- 28.6mm~38.1mm 15mm or more 88
- Unit: mm 89
- Absolute pressure 91
- Surface pressure (kg/cm 91
- Ordinary vacuum drying 92
- Special vacuum drying 93
- 30 or more 96
- Pipe mouth facing downward 96
- Air vent pipe 96
- Air vent device 97
- 5.1.1 MDS Series Indoor Units 98
- Model 1 setting (SW1.1 SW1.6) 98
- Address settings (SW2.1 99
- Model 2 setting 100
- SW3.5 SW3.8 100
- Power setting SW3.1 SW3.4 100
- Reserve 100
- Digital control 102
- 5.2 Trial Run 105
- Servicing and Maintenance 106
- 6.2 Servicing and Maintenance 107
- For example: 112
- WWW.MCQUAY.COM 116
Related products and manuals for Split-system air conditioners McQuay MDS080BR
(54 pages)© 2020, manymanuals.com. All rights reserved. | 5.142 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals