McQuay MDS080BR Installation Guide Page 106
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
-106-
Design & installation Guide For McQuay MDS Multi System
6.1 User Guide
6.1.1 Responsibilities and Obligations
This product is covered under MacQuay warranty during the warranty period.
Only MacQuay technicians or experienced professionals designated by MacQuay are al-
lowed to install, test, repair and maintain this product series.
6.1.2 Unpacking Inspection
Upon receipt of the units, please check them against the packing list. Check carefully if the
units are damaged during the transportation, and if all the components are complete and in good
condition. In case of any damaged unit or missing parts, please inform MacQuay's local branch
or dealer in writing immediately.
6.1.3 Using the Units
The total installed capacity of indoor units can be greater than but not more than 130% of
the capacity of outdoor units. However, when the total capacity of indoor units in operation
must not exceed that of the outdoor units. Otherwise, the output of each indoor unit can
reach their rated value;
All the indoor units are powered in a centralized manner. Before servicing and maintenance,
be sure to turn off the main power between the units;
After receiving the stop signal, each indoor unit will have its fan and electronic expansion
valve running for another 20~60 seconds, to make use of the afterheat or the cool air that
remains in the heat exchanger and also to get ready for the next start. This is normal.
When the running mode of the indoor unit is in conflict with the running mode of the outdoor
unit, the hand controller will display a message indicating this indoor unit stops running
because of the operation conflict. In this case, you can switch the indoor unit to a running
mode not conflicting with the outdoor unit, to restore the system to normal. The cooling
mode does not conflict with the dehumidifying mode, while the air supply mode does not
agree with any other mode.
The digital compressor adjusts the volume of refrigerant by opening and closing the PWM
solenoid. While the solenoid is operating, it clicks periodically. This is normal.
Servicing and Maintenance
CHAPTER
6
- CONTENTS 3
- Overview 4
- MDS080BR MDS100BR MDS120BR 7
- MDS150BR 7
- MDS200BR MDS220BR MDS240BR 8
- MDS180BR 8
- MDS280BR MDS300BR 9
- MDS260BR 9
- 1.3 Main Features 10
- Nominal capacity 11
- 100% operating 11
- 1.4 Nomenclature 12
- 1.5 Products Series 14
- 1.6 Performance Parameter 15
- 1.6.3 Ceiling Cassette 16
- 1.7 Operating Range 19
- 1.8 Refnet 19
- 1.8.2 C Type 20
- 1.9 Outline of Indoor Units 21
- 1.9.2 MDB050T 22
- 1.9.3 MDB060T 22
- 1.9.5 MCM020T MCM030T MCM050T 23
- 1.9.6 Auxiliary Heating Coil 24
- 1.10 Outline of Outdoor Units 25
- Unit Control 27
- Te m perature 28
- 2.3.3 Wire Control Panel 31
- 2.3.4 Outline and Dimension 31
- 2.3.5 Installation Type 31
- concealed installation 31
- 2.5 Network Central Control 34
- 2.6 Wiring Diagram 35
- Model MCK025/030/040/050T 36
- MCM020/030T 36
- Model MCM050T 37
- Model MDB050/060T 37
- Model MDS030A 38
- Model MDS030AR 38
- Model MDS040AR 39
- Model MDS040A 39
- Model MDS050A 40
- Model MDS050AR(220V~/50Hz) 40
- Model MDS060A 41
- Model MDS060AR(220V~/50Hz) 42
- Model MDS080/100/120B 43
- Model MDS080/100/120BR 43
- Model MDS150B 44
- Model MDS150BR 44
- Model MDS180B 45
- Model MDS180BR 45
- Model MDS200/220/240B 46
- Model MDS200/220/240BR 46
- Model MDS260BR(Master Unit) 47
- Connecting the master unit 48
- 2.7 Electric Connection 49
- 2.7.3 MDS080 240B/BR 50
- 2.7.4 MDS260 300B/BR 50
- 2.8 Electric Data 51
- Selection 52
- 3.2 Selection of Indoor Units 54
- Correction factor 57
- 3.4 Design of Air System 58
- 3.5 Slection of Refnet Joint 63
- For MDS-A series 64
- For MDS-B series 64
- Y type 65
- Type: MDS-Y5 65
- 3.6 Selection of E-EXV Box 66
- Installation 67
- Suspension ropes 68
- Protective pads 68
- (2 ropes) 68
- 4.2 Indoor Unit Installation 70
- (machine dimension) 820mm 73
- PULL PULL PULL PULL 76
- Height between indoor 78
- Refnet joint 80
- Outdoor unit 80
- Distributor kit 80
- Controller 81
- Indoor unit 81
- To indoor unit 82
- To outdoor unit 82
- Moisture 83
- Blind plug(copper) 84
- Flare fitting 84
- Avoid wielding too often 85
- Work flow 86
- NO.1 NO.2 87
- 6.4mm~25.4mm 10mm or more 88
- 28.6mm~38.1mm 15mm or more 88
- Unit: mm 89
- Absolute pressure 91
- Surface pressure (kg/cm 91
- Ordinary vacuum drying 92
- Special vacuum drying 93
- 30 or more 96
- Pipe mouth facing downward 96
- Air vent pipe 96
- Air vent device 97
- 5.1.1 MDS Series Indoor Units 98
- Model 1 setting (SW1.1 SW1.6) 98
- Address settings (SW2.1 99
- Model 2 setting 100
- SW3.5 SW3.8 100
- Power setting SW3.1 SW3.4 100
- Reserve 100
- Digital control 102
- 5.2 Trial Run 105
- Servicing and Maintenance 106
- 6.2 Servicing and Maintenance 107
- For example: 112
- WWW.MCQUAY.COM 116
Related products and manuals for Split-system air conditioners McQuay MDS080BR
(54 pages)© 2020, manymanuals.com. All rights reserved. | 0.137 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals